Environmental Engineering
.jpg)
Liquid Chromatography Mass Spectrometry Quadrupole Time of Flight
Liquid Chromatography (LC) separates components of a mixture.Mass Spectrometry (MS) with a Quadrupole Time-of-Flight (QTOF) analyzer precisely measures the mass-to-charge ratio of the separated components and provides high mass accuracy, resolution, and sensitivity.
Isotope Ratio Mass Spectrometer
The IRMS is designed for the precise measurement of the total element content and stable isotope ratio in a wide variety of gases i.e. H2, N2, NO, N2O, O2, CO, CO2,CH4, SO and SO2.
.jpg)
Gas Chromatography Mass Spectrometry
Gas Chromatography Mass Spectrometry is used for identification of compounds with low detection limits for quantitative analysis. It is used for volatile and semi-volatile compounds.
.jpg)
Basic Liquid Chromatography Mass spectrometer
Basic LCMS is used for chromatographic separation of organic molecules present in water samples, their identification and quantification using Diode Array Detector and Mass Detector.
TOC-TN Analyzer
TOC analyzer utilizes a catalytic oxidation combustion technique at high temperature (720 ºC), to convert organic carbon into CO2 which is measured with a NDIR detector. Chemiluminescence method is adopted for Total Nitrogen (TN) measurement.
.jpg)
Ion Chromatography
IC measures concentrations of ionic species by separating them based on their interaction with a resin. Measures concentrations of major anions and cations. Equipped with Conductivity detector, UV detector and Amperometric detector
.JPG)
Inductively coupled plasma mass spectrometry
ICP-MS is a type of mass spectrometry that uses an inductively coupled plasma to ionize the sample. It atomizes the sample and creates atomic and small polyatomic ions, which are then detected. Ability to detect metals in liquid samples at very low concentrations.
Attenuated Total Reflectance-Fourier Transform Infrared spectroscopy
ATR-FTIR spectroscopy is a non-destructive technique that uses mid-infrared radiation to analyze the chemical structures by measuring the infrared absorption spectrum of a sample.
 (1).jpg)
Potentiostat
The Autolab Metrohm M204 is a high-performance potentiostat/galvanostat is used for electrochemical measurements. It supports a wide range of techniques such as cyclic voltammetry (CV), linear sweep voltammetry (LSV), electrochemical impedance spectroscopy (EIS), corrosion analysis, and charge-discharge analysis.
Solar simulator
A solar simulator generates simulated sunlight to perform photocatalytic reactions under controlled conditions.
Direct Mercury Analyser
Direct Mercury Analyser (DMA-80) is used for analysis of total mercury and methyl mercury in solid and liquid samples where, total mercury of samples can be analysed directly after sample drying.
Autoclave
An autoclave is a high-pressure, high-temperature chamber used for sterilizing equipment, tools, and materials by using steam. It works by applying both heat and pressure to kill bacteria, viruses, fungi, and spores, ensuring that items are thoroughly disinfected.
Centrifuge
A centrifuge is a laboratory instrument used to separate the components of a mixture based on their density by spinning them at high speeds. The centrifugal force generated by the rapid rotation pushes denser components to the bottom of the tube, while lighter components remain near the center.
Laminar Air Flow Chamber
The Laminar Air Flow Chamber is a specialized enclosure designed to maintain a clean, controlled environment by providing a constant flow of filtered air over a workspace. The airflow is directed in a laminar manner, preventing contamination from airborne particles or microorganisms.
Lyophilizer
A lyophilizer, also known as a freeze dryer, is a laboratory and industrial device used to preserve perishable materials by removing water from them through a process called lyophilization or freeze-drying. The lyophilization process involves freezing a material and then reducing the surrounding pressure to allow the frozen water in the material to sublimate directly from solid to gas, bypassing the liquid phase.
Fume hood
A fume hood is a safety device commonly used in laboratories to contain and exhaust hazardous fumes, vapors, gases ensuring that harmful substances do not escape into the surrounding environment.
Water Purification System
The water purification system provides ultra pure type 1 water which is used in sensitive applications like reagent preparation, cell culture, chromatography, and molecular biology.
Particulate Sampler
A fine particulate sampler is an instrument used to collect and measure fine particulate matter (PM) in the air. The instrument is designed to target particles of specific sizes, typically focusing on the fine particulate matter.
Diffusion Cell Apparatus
A diffusion cell apparatus is commonly used in laboratory to study the diffusion of substances across membranes or interfaces.
Water Purification System
The water purification system provides ultra pure type 1 water which is used in sensitive applications like reagent preparation, cell culture, chromatography, and molecular biology.
pH meter
The bench top pH meter is used for measuring pH and temperature.
Conductivity meter
The Conductivity meter is a laboratory instrument used to measure the electrical conductivity (EC) of a solution, which is an indicator of the concentration of dissolved salts, minerals or ions in the solution.
Turbidity meter
The Turbidity meter is a specialized instrument designed to measure the turbidity of a liquid or a solution.
.jpg)
UV VIS Spectrophotometer
A UV-Vis Spectrometer (Ultraviolet-Visible Spectrometer) is an analytical instrument used to measure the absorption of ultraviolet (UV) and visible light by a sample. The absorption data is used to determine the concentration of specific compounds and study their properties.
BOD Incubator
The BOD incubator is used to maintain a constant temperature to encourage microbial activity during the BOD test.
.jpg)
Hot Air Oven
A Hot Air Oven is a laboratory equipment used for the sterilization, drying and heating of materials by circulating hot air inside an insulated chamber.
.jpg)
Muffle Furnace
A Muffle Furnace is a type of high-temperature furnace that is used for a variety of laboratory and industrial processes, primarily for heating, burning and drying materials in a controlled environment.
DO meter
A DO (Dissolved Oxygen) meter is an analytical instrument used to measure the amount of oxygen dissolved in water. This parameter is crucial for assessing water quality, especially in aquatic environments, wastewater treatment, and industrial processes where oxygen levels affect biological processes.
COD digestor
A COD Digestor (Chemical Oxygen Demand Digestor) is a device used to carry out the digestion process required for COD testing of water, wastewater and other aqueous samples.
Weighing Balance
Measures the mass of samples with great accuracy.
Magnetic Stirrer with Hot Plate
A Magnetic Stirrer with Hot Plate is a laboratory device that combines the functions of a magnetic stirrer and a heating plate in one unit. It is widely used in chemical, biological and pharmaceutical laboratories for heating liquids while simultaneously providing uniform stirring.
Autoclave
An autoclave is a high-pressure, high-temperature chamber used for sterilizing equipment, tools and materials by using steam. It works by applying both heat and pressure to kill bacteria, viruses, fungi and spores ensuring that items are thoroughly disinfected.
Membrane Fabricator
A membrane fabricator is used to prepare thin-film membranes with precise thickness for filtration and separation applications.
Annular type photocatalytic reactor
A annular type photocatalytic reactor uses a cylindrical design with a light source at the center to enhance photocatalytic reactions for pollutant degradation.
.webp)
Immersion type photoreactor
A immersion type photoreactor features a submerged light source to provide uniform illumination for photocatalytic or photochemical reactions.
Orbital Shaking Incubator
The orbital shaking incubator is used for incubation and gentle shaking or agitation of samples. This equipment is commonly used in biological, microbiological and biochemical applications to grow cultures, speed up reactions or mix substances uniformly while maintaining a controlled temperature environment.
Flocculator
The flocculator is used to simulate the coagulation and flocculation processes of water treatment.
Centrifuge
A centrifuge is a laboratory instrument used to separate the components of a mixture based on their density by spinning them at high speeds. The centrifugal force generated by the rapid rotation pushes denser components to the bottom of the tube, while lighter components remain near the center.
Optical Microscope
An optical microscope is a type of microscope that uses visible light and a system of lenses to magnify small objects, typically in the range of 0.2 micrometers to a few millimeters.
kjeldhal Apparatus
The Kjeldhal apparatus is a laboratory device used to determine the nitrogen content in organic compounds, such as food, soil or waste. It works by first digesting the sample in a strong acid, converting nitrogen into ammonia and then measuring the ammonia's concentration through a distillation and titration process.
Microwave Digester
A microwave digester is a laboratory instrument used to accelerate the digestion process of solid samples by using microwave energy. It utilizes controlled microwave radiation to heat and break down samples, typically to dissolve them in acids for chemical analysis, such as trace metal analysis (e.g., ICP-MS or ICP-OES). Microwave digestion is a key process in laboratories dealing with environmental, pharmaceutical, food, and material science research as well as in quality control and safety analysis.
Rotary Evaporator
A rotary evaporator (often referred to as a rotovap) is a laboratory instrument designed to efficiently and gently remove solvents from a sample through evaporation. It is commonly used in chemical, and biological laboratories for concentrating solutions, purifying compounds or separating volatile substances from non-volatile ones.
Bioreactor
The bioreactor is a specialized vessel or device designed to create a controlled environment for the growth of microorganisms, cells, or tissues.
.webp)
High Pressure Autoclave
A high-pressure autoclave is a specialized pressure vessel used to sterilize, treat, or process materials by subjecting them to high pressure and temperature.
Photoreactor
A photoreactor is a laboratory or industrial reactor designed to facilitate photochemical reactions, where light energy (usually ultraviolet (UV) or visible light) is used to drive chemical reactions. These reactors are used in various fields, including chemistry, environmental engineering and materials science to accelerate or control reactions through the energy of light.
Field Density Test - Core Cutter Method
The test procedure is based on IS 2720(Part 29) - The primary purpose of the field density test is to measure the in-place density of soil.
Field Density Test - Sand Replacement Method
The test procedure is based on IS 2720(Part 28) - The primary purpose of the field density test is to measure the in-place density of soil.
Orbital Shaker & Incubator
For precise temperature control and simultaneous shaking applications
Weighing Balance
Measures the mass of samples with great accuracy.
pH meter
The bench top pH meter is used for measuring pH, temperature and conductivity.
.jpeg)
pH meter
The bench top pH meter is used for measuring pH, temperature and conductivity.
TCLP Rotary agitator
A TCLP rotary agitator is a specialized intrument for the simultanious leaching of waste samples at different conditions with controlled speed and temperature.
.jpg)
Peristatic pump
A peristatic pump is used to transfers fluids with precision using flexible tubing and controlled flowrate.
Stirred cell membrane reactor
A high-pressure stirred cell reactor can be used to assess membrane performance such as permeability and fouling characteristics
Magnetic Stirrer with Hot Plate
A magnetic stirrer with a hotplate is a laboratory instrument used for stirring solutions under controlled temperature conditions.
DC meter
Measures direct current (DC) voltage and current.
Muffle Furnace
It is a high-temperature furnace that is used for a variety of laboratory and industrial processes, primarily for heating, burning and drying materials in a controlled environment.
Laminar Air flow chamber
For handling pathogenic biological samples or for applications that require a sterile work zone
Portable Autoclave
To kill microorganisms and spores using high-pressure steam to sterilize medical equipment, laboratory materials, and decontaminate biohazardous waste
Vaccum pump
A vacuum pump is used to remove air or gas molecules to create a vacuum.
Magnetic Stirrer with Hot Plate
A magnetic stirrer with a hotplate is a laboratory instrument used for stirring solutions under controlled temperature conditions.
DC meters
Measures direct current (DC) voltage and current.
-1.jpg)
Peristatic pumps
A peristatic pump is used to transfers fluids with precision using flexible tubing and controlled flowrate.
Fumehood
A fume hood is a safety device commonly used in laboratories to contain and exhaust hazardous fumes, vapors, gases ensuring that harmful substances do not escape into the surrounding environment.
-2.jpg)
Fate and Transport Set ups
Experimental set ups to understand the fate, transport, and transformaiton of micro/nanomaterials along with the aqeous ions